Y-axis motor bracket - Includes edge wire saddle - Holds the Y-Axis motor
Pincharm spring retaining bushing
Cutter bushing - Connects cutter assembly to slider rod
Pinch arm cam - Attached to pinch arm (Media) lever
Left cam journal - Mounted on left end of pinch arm shaft
Spindle end cap - Small core spacer - Removes for loading the media roll. Please order spindle assembly.
Carriage assembly - Includes carriage assembly, line sensor, encoder, rear bushing, calibration pen, digitizing sight, guages - Trailing cable and cable clamp not included
Encoder strip roof
One Line sensor lens cover for carriage - Mounts to carriage assembly for HP Designjet Plotters.
Right end cover - Has cut outs for the control panel
Left end cover for HP DesignJet 2000CP
Elevator platform assembly - Raises and lowers ink cartridges to fill the print heads - Located on left side of plotter
Cutter enclosure - Mounted above entry platen
Firmware SIMM kit (Revision A.04.08) - Mounts in the electronics module - NOTE: this is not a postscript SIMM
Overdrive gear cluster
Clutch / overdrive gear assembly - Includes gear, clutch, retaining clip, and two washers
Encoder ground strap - Provides ground to end of encoder strip
Starguard starwheel cover assembly
Housing assembly (on left side)
Hardware kit for printer stand - Includes screwdriver, screws, washers, and media bin retaining clips
Front wire link
SYNTHETIC OIL (4oz Plastic Bottle) Front and Rear Slider Rods Synthetic oil - One plastic bottle of 3.5oz / 118.29 ML
External JetDirect LAN interface module with RJ-45 connector for EtherTwist (10Base-T) or 100VG/802.12 input and three parallel (DB-25) output connectors
Bail motor for HP DesignJet 2500CP
Carriage (Y-Axis) motor assembly - Drives carriage belt - Includes motor, motor holder, and cable
Special lubricating oil - For carriage slider rod surface - (5cc oil)
Overdrive assembly (B) - Includes overdrive shims, clutch and overdrive gear
Paper for DesignJet 1055 Series, DesignJet 800 Series, DesignJet 130 Series, DesignJet 500. Bond Paper - 24 inch x 150.
Refill interconnect board
JetDirect 400N modular input/output (MIO) internal print server - Provides 10/100Base-TX or 10Base-2 network connection using RJ45 or BNC connectors
JetDirect 400N modular input/output (MIO) - Internal print server - Provides 10/100Base-T or 10Base-2 network connection using RJ45 or BNC connectors
External JetDirect token ring interface module with DB-9 and RJ-45 input connectors and three parallel (DB-25) output connectors
HP JetDirect 500X external token ring print server module - Interfaces up to 3 parallel printers to an ethernet 10Base-T (RJ-45), 10Base2 (BNC), or 100Base-TX (RJ-45) LAN
Pincharm assembly - Curved black plastic plate with four small rubber rollers - Does NOT include spring or bushing
Refill assembly - Mounted inside the left hand cover - Includes motor and gears
Paper drive (platen) roller assembly - Long gear driven roller - Includes roller and mark encoder
Right end cover and window closed sensors - Includes cable and connector
Pincharm sensor
Left end cover sensor - Includes cable and connector
Take-up reel sensor assembly
Service station assembly for Hewlett Packard Designjet Plotters.
Extension spring - Holds the rollfeed access cover closed
Compression spring - Installed between pincharm assembly and bushing
Service station spring
Starwheel mount assembly - Includes cover, body, spring and two starwheels
Encoder strip - Used to determine carriage position, 36inch.
Roller support bracket
Take-up reel left hand support assembly
Stand-by switch asembly
Right trim assembly - At right of entry platen
Left trim assembly - At left of entry platen