Bail assembly - Mounting strip assembly for the starwheel mount assemblies (Not included) - Extends width of plotter (D-size)
Carriage belt (D-size) - Long/wide belt attached to the carriage
Carriage motor bracket
Pincharm spring retaining bushing
RS-232C serial cable - 25-pin (M) to 8-pin (M) DIN - 1.5m (4.9ft) long
RS-232C serial extension cable - 25-pin (M) to 25-pin (F) - 5.0m (16.4ft) long
RS-232C serial cable - 25-pin (M) to 25-pin (F) - 1.2m (3.9ft) long
Ribbon cable with ferrite - Has 5-pin (F) connectors - 16.5cm (6.5in) long
Spindle end cap - Small core spacer - Removes for loading the media roll. Please order spindle assembly.
Ribbon cable clamp (top half) - Secures the trailing cable to the top of the carriage assembly
Ribbon cable clamp (bottom half) - Secures the trailing cable to the top of the carriage assembly
Cross-brace - Brace that connects and supports the two stand legs
Cutter mechanism assembly - Auto cutter for rollfeed paper
Mrk encoder for HP BAIPLY1Z
Tubeaxial fan for HP DesignJet 750C Series
Foot assembly (includes casters) - Mounts to the bottom of the plotter stand legs (two used)
Overdrive gear cluster
Clutch / overdrive gear assembly - Includes gear, clutch, retaining clip, and two washers
Cable holder (Small U-Shaped piece on top) - One of two pieces that hold the trailing cable to the main chassis
Housing assembly (on left side)
Hardware kit for printer stand - Includes screwdriver, screws, washers, and media bin retaining clips
Leg assembly - Side support for the plotter - Does NOT include the foot assembly
SYNTHETIC OIL (4oz Plastic Bottle) Front and Rear Slider Rods Synthetic oil - One plastic bottle of 3.5oz / 118.29 ML
16MB SIMM memory module
External JetDirect LAN interface module with EtherTwist (10Base-T) and ThinLAN (10Base-2) connectors
External JetDirect LAN interface module with RJ-45 connector for EtherTwist (10Base-T) or 100VG/802.12 input and three parallel (DB-25) output connectors
External JetDirect LAN interface module with EtherTwist (10Base-T) connector
Carriage drive motor assembly - Includes motor and cable
Paper (X-axis) drive motor (includes helical drive gear - NOTE: motor and gear are only sold as a set
Main Logic Pca Dj95xc 4m
JetDirect 400N modular input/output (MIO) internal print server - Provides 10/100Base-TX or 10Base-2 network connection using RJ45 or BNC connectors
External JetDirect token ring interface module with DB-9 and RJ-45 input connectors and three parallel (DB-25) output connectors
HP JetDirect 500X external token ring print server module - Interfaces up to 3 parallel printers to an ethernet 10Base-T (RJ-45), 10Base2 (BNC), or 100Base-TX (RJ-45) LAN
PostScript SIMM
Power cord (Mint Gray) - 2.0m (6.6ft) long - Has straight (F) receptacle (for 220V in Switzerland)
Daisy chain power cord (Dove Gray) - 18 AWG, 1.2m (4.0ft) long - Has C14 (M) plug for power input and C13 (F) plug for power output
Power Supply PC Board
Primer assembly - Mounts under the service station assembly on the left side of the plotter
Paper drive (platen) roller assembly - Long gear driven roller - Includes roller and mark encoder
Media sensor mechanical assembly
Sensor assembly
SIMM module shield
Compression spring - Installed between pincharm assembly and bushing
Compression spring - For the pulley wedge - Applies tension to the carriage belt
Starwheel mount assembly - Includes cover, body, spring and two starwheels
Encoder strip assembly (D-size) - Includes encoder strip and encoder strip spring
Pulley wedge tensioner - For carriage (Y-axis) belt tension