Universal AC power adapter - wide-range, 40c - Requires separate country-specific power cord with C7 connector
Left encoder bracket - Holds left end of encoder strip
Pincharm spring retaining bushing
RS-232C serial cable - 25-pin (M) to 8-pin (M) DIN - 1.5m (4.9ft) long
RS-232C serial extension cable - 25-pin (M) to 25-pin (F) - 5.0m (16.4ft) long
RS-232C serial cable - 25-pin (M) to 25-pin (F) - 1.2m (3.9ft) long
Ribbon cable - Has 5-pin (F) connectors - 16.3cm (6.4in) long
Carriage assembly trailing cable (E-size) - Has 60-pin (F) connectors - 1.9m (6.2ft) long
Bail lift cam - Mounted behind the bail engaging lever support
Left cam journal - Mounted on left end of pinch arm shaft
Right encoder clip
Trailing cable clip
Overdrive clutch assembly - Small, wide gear near overdrive gear - Held in place with a retaining E-ring
Carriage top cover
Cutter assembly - Mounts on carriage slide rod to the right of the carriage
Media deflector with media button - The media deflector furthest to the right side - Includes media load button
High gloss white film (4 mil) - 91.4cm (36in) x 30.5m (100ft) roll
Front panel assembly - Complete
Overdrive gear cluster
Bail engaging lever gear
Trailing cable guide (E-size) - Tray used to hold and guide trailing cable
Rollfeed guide kit - Left and right guides mounted under printer - Used to attach rollfeed housings to the printer
Holder - For Quick Reference Guide - On right end cover
Hardware kit for printer stand - Includes screwdriver, screws, washers, and media bin retaining clips
4MB, 70nS, 36-bit parity SIMM memory module
4MB, 70nS, 36-bit SIMM memory module - For HP LaserJet 4P, 4+, 4V, 5, 5N, 5M, 5P, 5Si
8MB, 70nS, 36-bit parity SIMM memory module
8MB, 70nS, 36-bit SIMM memory module - For HP LaserJet 4P, 4+, 4V, 5, 5N, 5M, 5P, 5Si
16MB SIMM memory module
16MB, 70nS, 36-bit SIMM memory module
Electronics module - Contains power supply main logic board interface connectors and fan
Electronics module - Contains power supply, Main Logic board, interface connectors, and fan
External JetDirect token ring interface module with DB-9 and RJ-45 input connectors and three parallel (DB-25) output connectors
HP JetDirect 500X external token ring print server module - Interfaces up to 3 parallel printers to an ethernet 10Base-T (RJ-45), 10Base2 (BNC), or 100Base-TX (RJ-45) LAN
Pincharm assembly - Curved black plastic plate with four small rubber rollers - Does NOT include spring or bushing
Power cord (Mint Gray) - 17 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (for 240V in the UK, Hong Kong, Singapore, Malaysia, and Brunei)
Power cord (Mint Gray) - 17 AWG, 2.0m (6.6ft) long - Has straight (F) receptacle (for 240V in Australia, New Zealand, and China)
Power cord (Mint Gray) - 17 AWG, 2.0m (6.6ft) long - Has straight (F) receptacle (for 220V in Europe, Bangladesh, Indonesia, Pakistan, Burma, Sri Lanka, and Vietnam)
Power cord (Mint Gray) - 2.0m (6.6ft) long - Has straight (F) receptacle (for 220V in Switzerland)
Wall mount power supply module - 120VAC input 60Hz power supply AC DC 15W UNIVERSAL ADAPTER Power module (wall mount)- Input voltage 100-240 VAC - Output voltage 12 VDC, 15 watts output, 1.0A - for Jet Direct power and other accessories.
Primer assembly - Mounted on left side of plotter
Setup printhead kit - Used to prime the ink tubes - Includes 4 setup printheads. Used to remove air and prime the ink system
Paper drive (platen) roller assembly - Long gear driven roller - Includes roller and mark encoder
Spittoon assembly - Contains absorbers which hold excess ink from cartridges
Bail gear support 'claw' spring - Attached between the bail engaging lever support and the bail gear assembly
Compression spring - Installed between pincharm assembly and bushing
Bail engaging lever support - Mounted over the left end of the drive roller - Bail engaging lever snaps into this item