Accumulator assembly
Accumulator assembly - Holds paper until print job finish then moves to stapler or correct output bin
Shutter arm for HP LaserJet M9040 MFP
IEEE 1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36-pin high density IEEE 1284C (M) connector (type C) - 10m (33ft) long
Toner cleaning cloth - Specially treated cloth for absorbing toner or Ink (1 per package) - Ideal for cleaning up toner spills and Ink for your plotter / copier / printer
Control Panel Assembly for HP LaserJet 9000 9040 9050 series models.
Control Panel Assembly
Lower left cover - Smaller plastic piece below left door and diverter assembly
Right front inside corner cover
Front inside cover - Cover behind front drop down cover
Right cover assembly - Includes all components attached to this door
Delivery assembly - Includes the curved plastic structure, various rollers and gears, and the L shaped metal support structure with three fans
Face-up delivery assemblyFace-up delivery assembly
Fuser delivery drive assembly - Includes gears, motor and microswitch for fuser drive - Also drives delivery roller
Paper input whole unit assembly - For printer/engine. PIU Paper Input Unit for LaserJet 9000 / 9000MFP / M9040 / M9050 / 9040 MFP / 9050 MFP and compatible units.
Sensor flag - Short rod with two flat flags and a curved end flag
Chassis foot - Support for right side of printer chassis - Two used
Fuser Assembly - For 100 VAC to 127 VAC - Bonds toner to paper with heat
Paper pickup guide - Plastic shaft with several fins on it - Mounts on the upper right side of the print engine frame assembly
Cartridge guide - Plastic structure with cartridge guide slot molded into it - Mounts on the upper front side of the registration assembly
5GB EIO hard drive
Front cover hinge
Fuser connector holder assembly
Jam removal knob
Laser/Scanner assembly - Mounts on the support structue in the print engine frame assembly
Latch mount assembly
16MB, 100-pin SDRAM DIMM memory module
32MB, 100-pin SDRAM DIMM memory module
128MB, 100-pin SDRAM DIMM memory module
Firmware Dimm Flash Memory 16MB Flash/32MB
64MB SDRAM - 100MHz synchronous DRAM - DIMM package
Offset module for 3000 sheet stacker
Drum feed drive motor
Front Fuser Assembly mount
Rear Fuser Assembly mount
Front pressure mount for toner cartridge
Rear pressure mount for toner cartridge
Paper path router - Mounts underneath the Paper Flipper assembly
Formatter board - Main Logic PCA
DC controller board assembly
Controller PC board - Tray 4 deck controller board - Controller PC Board - for 2000 sheet feeder - Uses data from volume and size PC boards to control paper tray
Low voltage power supply assembly - For 100V to 127VAC operation - Mounts on the upper rear of the printer
High voltage power supply board - Mounts on the upper rear of the printer
Power supply assembly
Front Fusing Rail
Rear Fusing Rail
Left lower rail assembly
Right rail assembly
Cartridge guide rail - Right side toner cartridge guide rail
Registration roller assembly
Transfer roller only - Includes the long black spongy roller roller shaft and drive gear - Transfers static charge to the paper
Feed separation pick-up roller - Rubber roller on a plastic collar with integrated gear and locking tab
Paper pick-up and feed roller assembly - Rubber roller with drive gear
Pick-up roller for optional tray 1
Separation roller - For tray 1 assembly
End paper sensor assembly - Contains Tray 2 and 3 paper length detection switches
Laser shutter - Cartridge shutter actuator - Piece that opens cartridge shutter as it is inserted into the printer
Torsion spring - Provides tension for bin full flag
Shutter arm spring - Provides tension for shutter arm
Compression spring - Provides tension for ON/OFF switch
Transfer roller assembly w/holder - Includes transfer guides holder chrome plate and transfer roller unit.
Optional Tray 1 assembly - Complete Tray 1 assembly including rollers and mechanical drives