ADF Tray : ADF input paper tray assembly - Holds 50 sheets of paper. Automatic Document Feeder (ADF) Input Tray For Hewlett-packard (HP) Printers
Door arm - White plastic arm that connects to left side cartridge access door
Bushing/shaft retainer (Plastic) - Small plastic cylinder with four nubs that twist - Locks into the side frame
Inner bushing - Rides on the large white 201-tooth drive gear.
Laser scanner motor cable - Connects ECU to scanner motor (M3).
Cam - Located between large white 201 tooth gear and drive release lever
Contact cam - Vertical piece that inserts into protective plate.
Cable clip - `C` shaped White plastic
Drawer connector - Connector located on top of tray assembly frame (right side) which connects tray assemblies to each other
Grounding contact - Tiny U-shaped metal cartridge grounding contact - Contacts copper grounding strip on left side of toner cartridge
Control panel assembly - Control buttons and display located on top front of printer;Click to order the functional equivalent: CB414-60157
Cover for main motor M1 - Located on lower right side of printer
Gear cover - Mounts on the left side of the printer chassis.
Right lower cover - Horizontal plastic cover - Mounts on the right lower side of the printer.
40GB SATA Hard drive - 5,400 RPM, 2.5 inch form factor, 9.5mm height Hard drive kit. For PATA (Parallel ATA) connector order Q7829-67935.
Drive release assembly -
Main drive assembly - Mounts on the right side of the printer - Metal plate with gears attached - Also known as main gear drive assembly.
Plastic duct that vents air from the lower right front fan to the laser/scanner.
Cartridge duct - Small vent duct to route air from the fan (FM1) to the cartridge area.
Fax printed circuit assembly (PCA) - Accessed from the rear of the unit - Located on the formatter boardHP LaserJet analog fax accessory 300
Lower paper feed assembly - Vertical transfer unit - Transfers paper from pickup assembly up to the printer input.
Sensor flag assembly for tray 2 - Short rod with one flag on it - Mounts next to the pickup roller assembly
Fuser Assembly - For 110-127 VAC - Bonds toner to paper by heat - Includes 20-tooth gear
Fuser Assembly - For 110-127 VAC - Bonds toner to paper by heat
Fuser thrust stopper - Located on the fuser drive assembly.
Gear - Pick up roller gear assembly
Gear - 30 tooth - Attaches to right side end of Tray 1 pickup roller shaft
Gear - 201-tooth gear
Replacement gear kit - Includes 17,17,19 and 20 tooth gears
17 tooth gear assembly - Includes the 17 tooth gear mounted on a black plastic lever/bracket
Duplexing pendulum assembly - Gear assembly that transfers power from main motor to run duplexing capability.
Grounding plate - High voltage power supply grounding plate - Attaches to left rear of power supply
Feed guide assembly - Mounts above transfer roller assembly
Door arm guide - White plastic guide for cartridge door lever
Cassette guide - Right rear side cassette guide.
Right center side plate guide
Cassette guide - Left side guide for media cassette.
Cassette guide - Left rear side cassette guide.
Center guide - Left center guide plate.
Air guide - Located next to the cartridge duct.
Cartridge guide - Lower right side toner cartridge guide.
Cartridge guide - Upper left side toner cartridge guide
Position guide assembly - Guides the paper along the right side duplex path - Attaches just above power supply
Plate holder - Holds the left rear corner of the paper access plate (duplex pan)
Reader holder cover - Plastic housing that covers cartridge E-label reader and holder assembly
Reader holder - E-label reader holder - Housing that holds cartridge E-label reader
Holder - Plastic assembly that holds optional input connector.
Main fan holder - Plastic fan holder for main cooling fan (FM1) - Located on the upper right side of the printer.
Holder - Plastic assembly that holds interlock switch for cover.
Fan holder - Chassis left fan holder
Switch holder - Holds the power on/off switch.
Link switch holder - Plastic guide that holds power link arm in place.
Laser/Scanner assembly - Mounts on top of print structure
Grounding contact lever - Lever on left side that is moved by contact when the toner cartridge is installed
Coupling lever - White plastic lever between large white gear cam and drive release assembly
Drive release lever -
Lever drive release
Cartridge clamp lever - Attaches to upper left toner cartridge guide - Provides mechanical lock for toner cartridge
Drive release link -
Laser shutter link - Enables the laser scanner shutter by pressing up this link on the underside of the laser/scanner assembly
Link switch - Metal arm that links power switch to power supply.
Control planel overlay - Snaps on top of the control panel assembly (English)
Formatter (Main logic) board - For HP LaserJet M3035/M3027 Series only
Engine controller assembly - For 110 VAC to 127 VAC - Engine controller PC board and metal pan - Provides all power supply and motor control functions
Engine controller assembly - 220-240VAC - Engine controller PC board and metal pan - Provides all power supply and motor control functions
Protective plate -
Plate face-up shield
Bottom support plate for the roller assembly
ADF feed roller assembly - Mounts in center of the ADF chassis - Includes gear, shaft, and clutch partsADF feed roller assembly - Mounts in center of the ADF chassis - Includes gear, shaft, and clutch parts
Face down roller - Small individual feed roller that rides against face down shaft roller - Held by torsion spring - Four used
Tray 1/MP Tray pickup roller - D-shaped replacement pickup roller
Paper pickup roller - Picks up media from the paper input tray.
Roller assembly - Black plastic housing that holds rollers in front of Tray 2 pickup roller assembly
Delivery roller assembly - Lower face-down output roller assembly - Includes roller and holder Four used
Pick up roller assembly -Tray 2/3 - LaserJet P3005 P3015
Paper sensor assembly - Paper present sensing
Paper width sensor - Printed circuit board (PCB) assembly.
MultiPack Qty 20 CST. PICK-UP ROLLER ASS
Torsion spring - Provides tension for top of page sensor flag
Torsion spring - Tiny spring that attaches to small metal U-shaped cartridge grounding contact - Rear cartridge contact spring
Torsion spring - Tiny spring that attaches to small metal U-shaped cartridge grounding contact - Front cartridge contact spring
Compression spring - Provides pressure to grounding contact link on left side of cartridge guide - Pushes link arm away when cartridge is removed
Torsion spring - Provides tension for Tray 1 paper sensor flag
Compression spring - Provides pressure for the large 201 tooth white gear on right side of printer
Tension spring - Provides tension for cartridge clamp lever that holds lefts side of cartridge in a stable position when inserted
Compression spring - Spring provides pressure to the laser shutter which when pulled back (spring is compressed) enables the laser scanner shutter by pressing up the plastic mechanical link on the underside of the laser/scanner assembly
Compression spring - Provides pressure for E-reader holder
Tension spring - Provides tension for cartridge access door arm
Torsion spring - Provides pressure to move protective plate back into cartridge compartment when the cartridge is removed
Left wing feed guide stopper
Left cartridge stopper - Provided a predetermined position for the cartridge
Microswitch - Door open switch - SW501
500-sheet input tray - Paper cassette for tray 3. (RM1-3732-000CN is tray# 2)